« previous next »
Pages: [1]   Go Down

Author Topic: 231 Rear Output shaft  (Read 1646 times)

KingtheZJ

  • Hero Member
  • *****
  • Posts: 2204
  • Karma: +0/-0
231 Rear Output shaft
« on: July 13, 2012, 10:20:12 PM »
picked up a case a while back that has a bent external slip yoke shaft. this is what would be left over if you did a SYE
Report to moderator   Logged

Wingman

  • Free Loader
  • Hero Member
  • ***
  • Posts: 4597
  • Karma: +2/-1
Re: 231 Rear Output shaft
« Reply #1 on: July 14, 2012, 07:30:49 AM »
So, you are selling the case or just the bent shaft?  Or need the shaft?
Report to moderator   Logged
Retired

KingtheZJ

  • Hero Member
  • *****
  • Posts: 2204
  • Karma: +0/-0
Re: 231 Rear Output shaft
« Reply #2 on: July 14, 2012, 08:49:26 AM »
need a new shaft
Report to moderator   Logged

Callelle

  • Hero Member
  • *****
  • Posts: 554
  • Karma: +1/-0
Re: 231 Rear Output shaft
« Reply #3 on: July 14, 2012, 10:06:50 AM »
I might still have my shaft from when I did my SYE. Ill take a look when I get home tomorrow.
Report to moderator   Logged

KingtheZJ

  • Hero Member
  • *****
  • Posts: 2204
  • Karma: +0/-0
Re: 231 Rear Output shaft
« Reply #4 on: July 18, 2012, 08:54:34 PM »
any word on this, Josh? i'm looking for it sooner than later
Report to moderator   Logged

Callelle

  • Hero Member
  • *****
  • Posts: 554
  • Karma: +1/-0
Re: 231 Rear Output shaft
« Reply #5 on: July 18, 2012, 11:27:45 PM »
Forgot about this, my bad. Just wrote down a note so Ill remember to check in the morning.
Report to moderator   Logged

Callelle

  • Hero Member
  • *****
  • Posts: 554
  • Karma: +1/-0
Re: 231 Rear Output shaft
« Reply #6 on: July 19, 2012, 11:35:53 AM »
I took a quick look this morning and didn't see anything. I didn't really look long because I had a family emergency in Henrietta, I'll take a more thorough look when I get home tonight.

Sent from my Samsung Galaxy S3 using Tapatalk.
Report to moderator   Logged

KingtheZJ

  • Hero Member
  • *****
  • Posts: 2204
  • Karma: +0/-0
Re: 231 Rear Output shaft
« Reply #7 on: July 19, 2012, 01:24:58 PM »
ok thanks
Report to moderator   Logged

Callelle

  • Hero Member
  • *****
  • Posts: 554
  • Karma: +1/-0
Re: 231 Rear Output shaft
« Reply #8 on: July 19, 2012, 06:38:00 PM »
I looked all over my shop and where my parts that I replaced were and couldn't find it. Must have gotten mixxed in with my last scrap run I did. Sorry Spencer.
Report to moderator   Logged

KingtheZJ

  • Hero Member
  • *****
  • Posts: 2204
  • Karma: +0/-0
Re: 231 Rear Output shaft
« Reply #9 on: July 19, 2012, 10:40:03 PM »
no worries. thanks for looking
Report to moderator   Logged
Pages: [1]   Go Up
« previous next »