1
Projects Section / Re: new buggy build
« Last post by mr.mindless on Today at 02:52:19 PM »nice and light!
Recent Posts
2
Projects Section / Re: 3 window chevy build on escalade chassis
« Last post by mr.mindless on Today at 02:51:58 PM »I commented on that when you left last night. sounded a lot like the drone Eric was looking to remove from his Ram. Excellent!
3
Projects Section / Re: new buggy build
« Last post by M4wdFab on Today at 12:17:30 PM »1570 lbs front
1580 lbs rear
3150lbs
With toolbag and fuel.
1580 lbs rear
3150lbs
With toolbag and fuel.
4
Projects Section / Re: 3 window chevy build on escalade chassis
« Last post by M4wdFab on Today at 10:38:07 AM »New quiet flow muffler installed this morning. Zero drone or any more claptrap shit sound. So much better and perfect amount of v8 when you stand on it.
Got its first hand wash!
Got its first hand wash!
5
Projects Section / Re: Brandy new 4500 Cummins
« Last post by M4wdFab on May 29, 2024, 01:34:46 PM »104K
oil change
fuel filters changes
rear pinion seal
fluid film touched up
oil change
fuel filters changes
rear pinion seal
fluid film touched up
7
Projects Section / Re: MMTR Mini
« Last post by mr.mindless on May 28, 2024, 07:01:54 AM »Worth looking at. Changing to draw straw for low pressure frame rail pump and making filler and mounts work seem like similar level of work overall.
Pic and dimensions?
All the car tanks I’ve had were way too wide. Nothing still around, I haven’t held onto them.
Pic and dimensions?
All the car tanks I’ve had were way too wide. Nothing still around, I haven’t held onto them.
8
Projects Section / Re: MMTR Mini
« Last post by M4wdFab on May 27, 2024, 08:05:58 PM »want a cobalt tank? toss that in the trash just put a boat tank or something modern in it lol
9
Projects Section / Re: MMTR Mini
« Last post by mr.mindless on May 27, 2024, 06:33:50 PM »Mitsubishi must employ child labor to put the pickup screen on the draw tube on this fuel tank.
And yes I did snap 2 of the 3 studs on the level sender. Studs don’t stick through. Dual wall on top it seems. Will be fun to drill those out
Or I just get a big hole saw out and give room to work and fix 2 problems. That may end up the way to go. No existing flat spot of course.
And yes I did snap 2 of the 3 studs on the level sender. Studs don’t stick through. Dual wall on top it seems. Will be fun to drill those out
Or I just get a big hole saw out and give room to work and fix 2 problems. That may end up the way to go. No existing flat spot of course.
10
Projects Section / Re: new buggy build
« Last post by M4wdFab on May 27, 2024, 12:51:09 PM »found some big rocks and AOAA and continued to push this thing.
im still super impressed but the OEM 1550 shafts are not going to cut it.
had steering locked both ends and just cresting a small turtle rock, idle crawling no impact or shock and snapped a rear outer stub like nothing.
just doing some quick research, i think ill try a pair of rear 4340 stubs first. then go biger money to 40 spline. stubs are on ebay right now for 156$ each. 40 stuff will be about 5K for both axles. bah.
im still super impressed but the OEM 1550 shafts are not going to cut it.
had steering locked both ends and just cresting a small turtle rock, idle crawling no impact or shock and snapped a rear outer stub like nothing.
just doing some quick research, i think ill try a pair of rear 4340 stubs first. then go biger money to 40 spline. stubs are on ebay right now for 156$ each. 40 stuff will be about 5K for both axles. bah.