next delphi auction up

[M4wdFab]

https://www.go-dove.com/events/22409 

129 lots
not much good this time.

[mr.mindless]

Couple maybe interesting things. I’ll have to see where they end up in a week. Trans jack would be nice, that’s the only one I remember after paging through last night.

[M]

My buddy who teaches Computer Integrated Machining Technology at NTID is really wanting that Haas CNC machine for his classroom.  He wishes that Delphi donated it to RIT/NTID for the students.

[M4wdFab]

i think RIT bought one of our dynos for next to nothing, cost us thousands to remove it.  doubt they will be doing anything for free / donating.  no money at all. 


my new trans jack just came in 208$ for a teloscoping 1100lb one. 
i bet it will go for stupid money but its a name brand nice one i think.  some of the numbers were real surprising last auction. 

[M]

Do you know who I can contact regarding IT equipment in the Delphi building?   My company could buy all of the phones, PCs, and networking gear if they're all decent.

[mr.mindless]

That’s cheaper than I’d have guessed. Nice.

Plan to cross shop closer to auction end for anything that isn’t bid up too high.

More interested in racking and tire machine and press and drill press than anything on that block.

[Harrison]

The belt sanders look nice

[mr.mindless]

closes tomorrow at 17:00


previous sander like this went for $420+18% - would be worth it at half that to me.
https://www.go-dove.com/asset/404/13309

wondering if the motor has low voltage wiring available. I think most do, but I think not all. is described as 3ph/480/60.

I'm sure the band saws are going to go for real money, the trans jack is nearing retail price already. gantry crane is interesting but not more than about $300 interesting, and its at 225.

both drill presses are of interest.
https://www.go-dove.com/asset/406/13309
https://www.go-dove.com/asset/366/13309

[M4wdFab]

belt sander and big band saw are just about the only two im interested in.  Ill walk down and look at the sander but pretty sure is 480 only. 


that little drill press and press are both nice, i have used them for years.  has foot petal start too. 

[M4wdFab]

anyone interested i have 2 extra drill press's id sell, my 1/2hp Delta from old shop (150$) and the bigger one i bought at auction for the mill vice.  12 speed 3/4hp with foot control (350$).  ill put them up on FB when i get around to it.  both are free standing and great units, 120v1ph.

[M4wdFab]

that iron crafter is an 8000lb machine 

id love it, but it would have to live down stairs lol 

https://surplusrecord.com/cgi-bin/adpop.pl?115935

[mr.mindless]

I looked at that. Said it’s beyond my sanity and ability and worth

If I can’t grab one of those at auction I might do your 3/4 horse

[cracker]

awesome.. built right in Honeoye.. I never knew there was that type of manufacturer here

[M4wdFab]

nick and I were talking about how to get his fork lift over to my place to use them both to lift it off my truck.  it throw 8K on the RAM no problem, rear axle rated at 13K.  need some serous i beams under my floor though to hold my truck, 8K, and 12K in fork lifts lol 

[mr.mindless]

Seriously.

I think I could move my forklift anywhere with a lift easily. Just pick and set on my bed.

Haven’t had 5k on my bed before, but have probably done 4500 in pin weight. But my 2500# lift does not help an 8k job much.